Where Is the Garbage Disposal Reset Button
Yes, most garbage disposals have a reset button. It’s usually a small red button on the bottom or lower side of the unit. If your disposal is humming but not spinning, or if it stopped working completely, this button is your first stop.
We found that a tripped reset button is one of the most common reasons a disposal goes silent. This happens when the motor overheats from running too long or jams on something hard. The reset button is a built-in safety switch that cuts power to protect the motor from damage.
- Look for a small red button on the bottom of the disposal unit.
- Press the button firmly until you hear a click.
- Wait a few minutes for the motor to cool down before pressing reset.
- If the button pops back out, there is likely a jam inside the unit.
- If it still won’t work after resetting, check the circuit breaker or outlet.
Below, we’ll walk you through exactly how to find the reset button, how to reset it safely, and what to do when pressing it doesn’t fix the problem. Let’s get your disposal grinding again.
Where to Find the Reset Button on Your Garbage Disposal
You need to get down low and look at the bottom of the unit. The reset button is almost always on the underside of the disposal housing, facing the floor. It is a small, raised button that is usually bright red, though some older models might have a black or white one.
It sits near the center where the motor is. You might need a flashlight to spot it if your sink cabinet is dark. Get comfortable, because you will likely be lying on your back or crouching to see it clearly. It is a simple round button, usually about the size of a pencil eraser. If you see a red button on the side of the metal cylinder, that is the one we are talking about.
Why Is the Reset Button There?
Think of the reset button as a circuit breaker for your disposal. It is a safety feature designed to protect the motor. When the motor gets too hot, or when it draws too much current because of a jam, the internal overload switch trips. This cuts the power instantly.
We found that this prevents severe damage to the motor windings. Without this switch, a locked-up motor would burn out quickly. The reset button is your signal that the safety switch has been activated. It pops out slightly when tripped. Pushing it back in restores power, but only if the underlying problem is gone.
Step-by-Step Guide to Resetting Your Disposal
Resetting a garbage disposal is a quick fix that takes less than a minute. But you need to do it safely. Follow these steps in order, and you will have the best chance of success without hurting yourself or the appliance.
Step 1: Turn Off the Power
Safety comes first. Do not reach under the sink with the power on. Go to your electrical panel and flip the breaker for the kitchen or the disposal circuit to the off position. If your disposal is plugged into an outlet under the sink, unplug it. This is a non-negotiable step. You are working near water and metal, and the risk is not worth it.
Step 2: Check for a Jam
Before you press the reset button, you need to make sure nothing is stuck in the grinding chamber. Look inside the sink drain with a flashlight. Remove any visible objects. Use tongs or pliers to pull out silverware, bottle caps, or bones. Never stick your fingers into the drain, even with the power off.
Many experts say that a jam is the main reason the reset button trips. If something is wedged in there, the motor cannot spin, which causes it to overheat. Clearing the jam is essential. If you cannot see anything, try manually turning the motor from underneath. There is a hex socket on the bottom center of the unit. Use a hex wrench to rotate it back and forth to break up a hidden jam.
Using the Manual Hex Wrench
Most disposals come with a small Allen wrench. It fits into the center hole on the bottom of the unit. Insert it and turn it clockwise, then counterclockwise. You are trying to free the flywheel inside. If it moves freely, you have cleared the jam. If it is stuck, keep applying gentle pressure until it breaks free.
Step 3: Press the Reset Button
Once the power is off and you have checked for jams, locate the button. Press it firmly with your finger or a blunt object. You should feel a distinct click. That click tells you the switch has re-engaged. It should stay in when you remove your finger. If it pops right back out, the motor is still overloaded, or the internal thermal switch is still hot.
Do not force it. If it does not stay in, wait a few minutes. The motor needs time to cool down. We found that waiting ten to fifteen minutes is often the difference between a successful reset and a failed one. The thermal overload needs to cool to a safe temperature before it will accept the reset.
Step 4: Restore Power and Test
After you press the button and it stays in, turn the breaker back on or plug the unit back in. Run cold water into the sink. Flip the wall switch to turn on the disposal. Listen for the hum of the motor spinning. It should run smoothly. If it works, great. Let it run for a few seconds to clear out anything left inside.
If it still hums but does not spin, you have a different problem. The motor might be getting power, but the flywheel is still stuck. Turn it off and repeat the manual turning process. If the motor does not run at all, move on to the next section.
What to Do When the Reset Button Does Not Fix It
Sometimes, the reset button is not the magic bullet. If you have followed all the steps and the disposal is still dead, you need to dig deeper. There are a few common culprits to check before you call a plumber or buy a new unit.
Check the Electrical Connection
First, verify that power is actually reaching the disposal. If it is plugged into an outlet, check the outlet with a lamp or a phone charger. A GFCI outlet (the ones with the “Test” and “Reset” buttons) might have tripped. Press the reset button on the outlet itself. If it is hardwired, check the circuit breaker again. Sometimes a breaker looks like it is on but has tripped to the middle position. Flip it fully off, then fully on.
Listen for a Humming Sound
Turn the switch on and listen carefully. If you hear a low hum, the motor is receiving power. The problem is a mechanical jam that is too severe for the wrench to fix. If you hear nothing at all, the motor might be burned out. A burned-out motor often has a burnt electrical smell. According to appliance repair guides, this happens when the overload switch has been tripped too many times without fixing the root cause.
When to Call a Professional
If you have checked the power source, cleared all visible jams, and the reset button still trips immediately, it is time to call an appliance repair technician. Continuing to reset a disposal with a serious internal fault can cause permanent damage. A technician can test the motor windings and the internal overload switch with a multimeter. Replacing the disposal might be cheaper than a repair visit, but a pro can give you the definitive answer.
Common Reasons the Reset Button Trips in the First Place
You can avoid the hassle of a tripped reset button by understanding what causes it. We found that most trips fall into three main categories: overloading, jamming, and overheating. Knowing these can help you change your habits and extend the life of your disposal.
| Cause | Description | Prevention Tip |
|---|---|---|
| Hard Objects | Bones, fruit pits, or metal utensils get stuck. | Only feed soft food scraps. Throw hard items in the trash. |
| Overloading | Too much food is pushed in at once, slowing the blades. | Feed scraps gradually. Let the disposal finish before adding more. |
| Overheating | Running the unit without water for a long time. | Always run cold water during and after grinding. |
What Not to Put Down Your Disposal
Many people treat the disposal like a trash can, but that is a mistake. Fibrous foods like celery and corn husks can tangle around the blades. Grease and oil can coat the internal parts and cause them to stick. Starchy foods like potato peels can turn into a paste and clog the system. Coffee grounds are fine in small amounts, but they can accumulate and cause a jam over time.
We found that sticking to soft, small scraps is the best policy. Think of the disposal as a final rinse for your plates, not a garbage compactor. If you wouldn’t chew it easily, it probably should not go down the drain.
How to Reset a Garbage Disposal Without a Button
Some older or budget-friendly models might not have a visible reset button. If you look at the bottom of the unit and see nothing, do not panic. The overload protection might be built into the power cord or the wiring. In these cases, the circuit breaker or the GFCI outlet is your reset. You will need to locate the breaker in your panel and reset it there.
If you have a model without a button and the disposal stopped, the fix is usually at the breaker box. Turn the breaker off for a few minutes, then turn it back on. This gives the internal thermal fuse time to cool down. If the breaker trips again immediately, you have a short circuit or a motor failure.
Checking the Reset Button on Specific Brands
While the red button is standard, there are slight variations. Insinkerator models have the button on the bottom, facing the floor. It is red and fairly large. Waste King models also have a red button on the bottom. We found that the placement is consistent, so if you know the brand, you still need to get underneath to look. The process is identical across most major brands. The key is to look for the button, not a specific logo.
Quick Troubleshooting Checklist
- Turn off the power at the breaker or unplug the unit.
- Remove any visible debris from the drain opening.
- Use the hex wrench to manually turn the motor and clear jams.
- Wait 10-15 minutes for the motor to cool down.
- Press the red reset button until you hear a click.
- Restore power and test with cold water running.
Conclusion
Dealing with a dead garbage disposal is frustrating, but the reset button is usually the simplest fix. We walked you through finding that small red button, clearing jams, and waiting for the motor to cool down. Nine times out of ten, a firm press after a ten-minute wait gets things spinning again. If you’re considering an upgrade, our guide to the quietest garbage disposals can help you choose a quieter model.
You now know the common culprits behind a tripped reset, like hard objects or running the unit without water. Stick to soft scraps and always run cold water, and you will avoid most of these problems. If the reset button keeps popping out or your disposal still won’t run, don’t keep forcing it. That is your cue to call a professional. Your safety matters more than saving a repair fee.
Start by checking the bottom of your unit for that red button. You will likely have your disposal back in action within minutes.
Frequently Asked Questions
Is the reset button on a garbage disposal supposed to pop out?
Yes, the button pops out when the internal overload switch trips. This is a safety feature that cuts power to the motor. A popped-out button is your signal that something caused the motor to overheat or jam. Press it back in only after you have cleared the problem.
How long should I wait to reset my garbage disposal?
You should wait at least 10 to 15 minutes after the motor stops working. This gives the internal thermal switch enough time to cool down. We found that pressing the button too soon will cause it to pop right back out. Patience here saves you from repeated failed attempts.
Can I reset a garbage disposal with the power on?
No, you should never press the reset button while the power is on. Always turn off the circuit breaker or unplug the unit first. You are reaching under a wet sink, and the risk of electric shock is too high. Safety is a quick step that takes seconds.
Why does my garbage disposal reset button keep tripping?
A reset button that keeps tripping means the motor is still overloaded or jammed. There is likely a hidden object stuck in the grinding chamber. You might also have a worn-out motor that draws too much current. If it trips again right after resetting, call a technician for a proper diagnosis.
Is a humming garbage disposal a sign the reset button needs pressing?
A humming sound means the motor is getting power, but the flywheel is stuck. Pressing the reset button will not fix a jam. You need to turn off the power and use the hex wrench on the bottom of the unit to manually rotate the motor. Once the jam is cleared, then check the reset button.
